Monday, September 23, 2013

THE CONSTRUCTION OF A SHOE

The Construction of a Shoe


Over one hundred operations go into the construction of a shoe.

  • The first and most important of these is the creation of the last.
  • The last is a hand-carved wood or molded plastic replica of the human foot.
  • The last determines the contour of the arch and how evenly the wearer’s weight will be distributed throughout the foot. A different last is required for each shoe style and size to be produced.
  • Before a shoe can be made, as many as thirty-five measurements are taken from a footprint to show the distribution of the body weight.
  • The maker judges the symmetry of the toes, calibrates the girth of the instep and ball of the foot, and calculates the height of the big toe and the contour of the instep.
  • He or she must also estimate how the foot will move inside the shoe.
  • All of these ratios must be addressed without compromising the architectural beauty of the shoe design.
For a heeled shoe, the maker visualizes the heel height, than determines the size of the throat. Next the appropriate height of the shoe’s quarter is established.

  • If it is too high it will rub the tendons, and if it is too low, the shoe will fail to grip the foot properly.
  • Crucial to the fit of a shoe is the measurement of the shank curve, including the ball and instep. This is where the body’s weight falls when the foot is in motion.
  • Using the last as a guide, the pattern maker cuts out the shoe upper and lining.
  • The edges are then beveled to ensure a good fit and the pieces are then sewn together. Next, a toe box is constructed, the counter is added, and the leather is soaked so it will easily conform to the lines of the last.
  • The upper is positioned on the last, tautly stretching it before nailing it tightly onto the last. The upper dries on the last for two weeks before the sole and the heel can be attached.
  • The final steps are to trim the welt, pare the heel, burnish the sole and add the insole lining. Last the shoe is polished and buffed, and it is ready for sale.

Wednesday, August 28, 2013

HOW TO SHINE A PAIR OF DRESS SHOES

Nothing undermines a nicely tailored suit like dull, worn-looking footwear. And while you can—and probably do—pay someone else to buff your oxfords to a perfect shine, there are times, especially when traveling, that you’ll need to do it yourself. Here’s how.

You will need:
A cloth or old T-shirt. An “on” brush or another old T-shirt. A toothbrush. Cream polish or wax polish. An “off” brush. A chamois, or yet another old T-shirt. Elbow grease (though really, you should polish from the wrist, not elbow).
NOTE: There are two types of polish, cream and wax. Cream makes the leather supple and wax improves water resistance. Both are fine qualities in a shoe, so it’s best to alternate between the two, using a different one each time you shine.

Step 1: Remove shoe trees and laces. Many people don’t bother taking the laces out, but it’s important to avoid getting polish on them, and to shine the tongue, which will start to look different to the rest of the shoe over time if it’s skipped.


Step 2: Put one hand into the shoe, palm down. In your other hand, with a cloth or T-shirt that is barely damp, gently wipe each shoe to remove dirt and grit; if these remain on the shoe’s surface when you shine it, the shoe will scratch.

Step 3: Make sure the shoes are dry, then apply apply the polish with an “on” brush, whose bristles are about half as short and stiffer than those on the “off” brush you’ll be using later, or with an old T-shirt (not the scratchy part with your college logo on it). Whatever you use, make sure you work the polish into every part of the shoe. You’ll probably need to go over the heel and toe twice, as these areas get the most wear.
Use a toothbrush to get polish into crevices, such as the area around the bottom of the upper, and the top of the vamp, which, unless you take taxis everywhere, is prone to creasing. Also shine the part of the sole that doesn’t touch the floor, between the heel and toe—there’s nothing more embarrassing than exposing a pair of unshined shoe soles when you wake up on the floor of an unfamiliar apartment (this may require a different-colored polish). Once you’ve worked the polish into the first shoe, set it aside for the cream or wax to sink in, and repeat these steps for the second one.

Step 4: Next, remove the polish from the first shoe with a horsehair “off” brush: this is the one time when a T-shirt won’t do, and if you’re going to be shining shoes of different colors, it’s worth getting different brushes for each one. Brush the shoe vigorously, with medium pressure. The ideal motion involves rapid movement of the wrist, with most of the arm stationary as the wrist moves the brush over the shoe in quick, short motions. Doing this means that each bit of leather receives more stokes than it would if you were moving from the elbow, which gives longer strokes. It also generates more heat on the surface of the shoe, which helps the polish sink in.


Step 5: When you’ve removed polish from both shoes with your brush, go over them with a chamois or old T-shirt, removing any excess you may have missed – pay particular attention to the top of the shoe, where polish often collects before finding its way onto your trouser cuffs later. Buff each shoe to a high shine with the chamois, admire your reflection in the toe of each shoe, and consider the job done.
 

Friday, June 7, 2013

THE ANATOMY OF A SHOE


The Anatomy of a Shoe

Shoe Anatomy Diagram

Breast: the front of the heel under the arch
Cap: the toecap
Counter: overlaid piece at the back of the upper
Feather: the part of the last and the shoe where the upper’s edge meets the sole
Insole: a piece of leather or other material between the sole and the foot
Puff: a light reinforcing inside the upper which gives the toe its shape and support
Quarter: the part of the back of the upper, which covers the heel
Seat: the concave part of the heel that fits into the shoe and into which the heel of the foot sits
Shank: a piece of metal inserted between the sole and the insole lying against the arch of the foot
Sole: the piece of leather or other material that comes in contact with the ground
Stiffener: the inside stiffening of the upper, covering the heel and giving the back of the shoe support
Throat: the front of the vamp
Top Piece: the part of the heel that comes in contact with the ground.
Topline: the top edge of the upper
Upper: the piece of the shoe that covers the foot
Vamp: the part of the upper that covers the front of the foot as far as the back as the joint of the big toe
Waist: the part of the last and the shoe that corresponds to the arch and instep of the foot

Thursday, May 30, 2013

CARING FOR YOUR FOOTWEARS

FOOTWEAR

Footwear is made of leather because it is comfortable, supportive, naturally water-repellent and breathable. The less water absorbed by leather, the longer it will last and the more comfortable your feet will be. Once wet, leather stretches and weakens, shrinks and becomes brittle as it dries. Here are a few simple suggestions to keep footwear performing at their best for years to come.

Cleaning

The first step to footwear maintenance is regular cleaning. Small particles of dirt can work their way into the fibres of the leather causing abrasion and break down. After use, rinse off mud and dirt with tap water. To remove oil-based dirt, excess wax and stubborn grime that will not be cleaned by plain water use Nikwax Footwear Cleaning Gel and a nylon brush. Be sure to clean the linings of your boots with a warm damp cloth after each use as well. Salt from perspiration can pass into the lining rapidly destroying the leather making it dry and cracked.

Re-proof or add water repellency

This is important not just to keep your feet dry, but will keep footwear cleaner and maintain the leather's suppleness for improved durability. After cleaning footwear with water, apply the appropriate Nikwax waterproofing treatment to the entire shoe or boot, paying special attention to the stitching and around hardware (anywhere the leather has been punctured) to ensure complete protection from the elements. Reapply as necessary or after use in severe conditions. For best results let footwear dry for 24 hours before use.

Drying

Start by removing the laces and inner soles. Dry footwear slowly at room temperature. Do not expose shoes or boots to a direct heat source. Excessive heat can cause irreversible damage to the leather and is harmful to the adhesives used in footwear construction. To help dry footwear that has been filled with water or is thoroughly soaked we recommend stuffing it with newspaper. Replace wet newspaper and repeat until footwear is dry.

Conditioning

Conditioning footwear can reduce the break-in time for new smooth leather shoes or boots and also revive old dried out footwear. We suggest using Nikwax Conditioner for Leather, a few times a year or as needed.

New Boots

To get the best results from your new boots or shoes, we recommend the following:

Fit

New footwear should be worn indoors for a few days to ensure that you are pleased with the fit

Comfort

When breaking in new boots be sure to wear the socks that you will be using with the boot.

Time

Allow adequate time to break in your new footwear. Heavier boots may require more time to break in. Start out with short walks working your way up to longer hikes. This will help guarantee your comfort and satisfaction.

Condition

If the boots are smooth leather and you have decided  that they are a good fit then Nikwax Conditioner for Leather can be applied to help break in your new boots.

Waterproof

After the boots have been worn in the outdoors a couple of times and the factory applied DWR (durable Water Repellency) is beginning  to wear off apply the appropriate Nikwax waterproofing treatment to extend the life of your footwear.

A short interview about James onyebuchi on vanguard news paper

http://www.vanguardngr.com/2013/05/if-you-dont-have-reason-for-waking-up-sleeping-becomes-interesting-linus-okorie/facebook.com/aidinitiativeng

Wednesday, May 8, 2013

TOE PAIN


Toe pain is one of the most common types of foot pain. Wearing ill-fitting or narrow shoes regularly is a frequent cause for toe pain. Shoes with narrow toe boxes can cause blisters, calluses, corns, and ingrown toenails, and can worsen other conditions, including bunions, hammertoes/claw toes, and Morton's neuroma.
The five toes (phalanges) and their connecting long bones (metatarsals) comprise the forefoot. Each toe (phalanx) is made up of several small bones. The big toe (hallux) has two phalanges, two joints (interphalangeal joints), and two tiny, round sesamoid bones. The other four toes each have three bones and two joints. The phalanges are connected to the metatarsals by five metatarsal phalangeal joints at the ball of the foot.
In addition to ill-fitting and narrow shoes, other common causes for toe pain include skin conditions, such as dry, cracked skin, eczema, and psoriasis; fungal infections, such as athlete's foot; bacterial infections; frostbite (i.e., damage to the skin and sometimes the underlying tissue caused by extreme cold); and fractures and bruises.
Gout is a disease caused by the buildup of uric acid in the joints that can cause severe toe pain. Gout usually affects the first metatarsal phalangeal joint of the big toe (hallux), the ankle joint, or the heel.
In addition to severe toe pain, gout may cause swelling, inflammation, redness (erythema), warmth, and stiffness.

Saturday, April 27, 2013

TIPS ON FOOT PAIN

Overview Foot pain is very common—most people experience some type of foot pain during their lifetime. Pain can occur anywhere in the foot, including the toes, the ball of the foot, the arch, the instep, the sole, the heel, and the ankle.
The incidence of foot pain increases with age.
The three main parts of the foot are the forefoot, the midfoot, and the hindfoot.
The forefoot consists of the toes and the connecting long bones (the metatarsals).
The midfoot, or arch, consists of five irregularly shaped tarsal bones, which are connected to the forefoot and hindfoot by muscles and the plantar fascia (arch ligament).
The hindfoot, which is comprised of three joints, links the midfoot to the ankle (talus) and includes the heel bone (calcaneus). The heel is the largest bone in the foot and it joins the talus to form the subtalar joint.
The bottom of the heel bone is cushioned by a layer of fat.

Keep following post as we share most secrets on foot pain and how to prevent them.